How to Set up a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround

How to Set up a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround

Blog Article

This Post

We've unearthed this article involving Installing A Bathtub listed below on the internet and think it made sense to talk about it with you over here.

How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is also a reasonably tough job. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and also place the new bath tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. Make certain you have certified yourself for the job and also are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to consider using one before you start. Possibilities are you may require a professional plumber to make tube links.
This article will certainly help you mount a new bath tub in your restroom if you have actually already acquired a new bathtub as well as do not need to transform the plan of your previous water pipes.
Your devices and material list ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps

  • Removing Old Touches

    If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is commonly the case.
    Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
    Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Suitable New Touches

    If the tails of the brand-new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a link to the existing supply pipes.
    If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines remain in location between the faucet as well as the sink. Protect the tap in position with the maker supplied backnut. Once the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Mounting the Tub

    Utilizing both wood boards under its feet, place the bath tub in the needed position. The wood boards are valuable in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
    The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the level checks out level.
    To install faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
    Turn on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
    Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub should wait till the tub has actually been utilized at least when as this will resolve it into its last setting.

    Preparing for the Setup

    Firstly, the sustaining framework provided with the bath should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
    Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washing machines.
    Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.

    Tiling Around the Bathtub

    In the area where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall between the bath and the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can crack fairly very early if you do not take into consideration this motion prior to sealing.
    Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water resistant adhesive and also grout.

    How to Install a Freestanding Bathtub?

    Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

    This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.


    Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.


    A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

    According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

    Clean the bathroom floor

    After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

    Steps to Install a Freestanding Bathtub:

    STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

    STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

    STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

    STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

    STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

    STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

    Tips to Maintain a Freestanding Bathtub:

  • Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.

  • Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.

  • Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.

  • Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.

  • Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.

  • If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.


    How to Install a Bathtub

    We had been shown that report on How to Install a Bathtub through a good friend on a different web address. Enjoyed our blog entry? Please share it. Let other people discover it. Many thanks for your time. Please visit our site back soon.

    Free Estimate

    Report this page